RTMC400-232CAN Controller

RTMC400-232CAN-A  $189.95 User Manual

RTMC400-232CAN-B  $199.95 User Manual

RTMC400-232CAN-C  $195.95 User Manual

RTMC400-232CAN  is based on a high-performance 16-bit 40 MIPS DSP core processor with enhanced peripheral interface. The advanced firmware has been developed and embedded in this controller so that the customer neither needs to develop real-time embedded firmware nor needs development tools. To command this device, the user simply sends ASCII strings or Modbus protocol  through RS232 serial port to do speed control, position control, speed measuring, position measuring, stepper motor control, read A/D, output D/A and PWM, set I/O or read I/O, etc. You can choose to have the returning data in either ASCII format or binary format based on setup configuration. Each A/D input can be filtered or passed through as raw data. This controller is capable of automatically recognizing ASCII protocol and Modbus protocol. For more details, click here to download user manual for RTMC400 Series Controllers (PDF).

This unit functions as a master and through its daisy-chainable connectors, such as RJ-45 Jacks or J4 header connector, up to 63 boards of RTMC200-CAN can be connected to form a distributed networking system

The ASCII string commands are intuitive and simple. For example, @1XS 2000 will set the speed reference to 2000 rpm for this controller at device address 1. @2RAU3 will read the A/D channel 3 with raw data from a slave controller, such as RTMC400-CAN at device address 2.

We offer three different board assembly configurations to give you a flexibility to choose the one that fits your hardware interface. The RTMC400-232CAN-A has no 0.1" pin header connectors installed; the RTMC400-232CAN-B is fully populated with 0.1" headers and terminal blocks as shown in the above picture; the RTMC400-232CAN-C is specially to be used as a daughter board with all 0.1" pin header connectors installed for daughter board interface. All of the three different boards function the same as stated in RTMC400 series User Manual.

 Features:

• 16-bit 40 MIPS DSP core controller.

• Built-in RS-232 to CAN bridge for networking

• Function as a master in the virtual UART communication networking

• 16 channels,10-bit A/D Sample & Hold with programmable sampling rate up to 30 kHz.

• 2  channels, 12-bit D/A with programmable sampling rate up to 30 kHz.

• 3 16-bit PWM outputs with programmable carrier frequency up to 30 kHz (symmetric waveform).

• Speed PI controller + Position PI controller with control sampling frequency up to 30 kHz.

• 7 Inputs digital I/O TTL compatible.

• 9 Outputs digital I/O TTL compatible.

• Digital filter on each A/D input.

• Built-in Watchdog capability.

• 1 Quadrature encoder supporting 200 - 8000 lines of optical encoder.

• 2 stepper motor indexers

• EEPROM for all configuration parameters.

• RS232 Communication to PC computer and CAN communication for networking

• Daisy-chainable communication for the board of RTMC400-CAN up to 63 nodes.

• Support simple ASCII string commands for both RS-232 and CAN bus.

• Support Modbus protocol for RS-232.

• 6.5-12 V DC daisy-chainable power supply .

• Compact size: 3.75" x 2.5" (9.6 x 6.3 cm) .

Connectors:

• 0.1"  20-pin double row header for J1 (Analog Inputs Interface)
• 0.1"  5-pin single row header for J8 (Digital-to-Analog Interface)
• 0.1"  40-pin double row header for J2 (I/O Interface)
• 0.1"  3-pin single row header for J14 (Power Supply)
• 0.1"  3-in single row header for J4 (RS-485 Interface)
• DB9 RS-232 standard communication connector J10
• 0.1" 2-pin single header for K2 (Jump for default communication set)
• 2 RJ-45 Jack connectors for J5 and J6 ( daisy-chainable CAN Interface)
• 0.1"  2-pin single row header for K1 (Jump for daisy-chainable power supply)
• 0.1"  2-pin single row header for K3 (Jump for 120 Ohm terminal resistor)